MaxiStick Blowpipe

Description
Customer Reviews
Questions and Answers

This May be the least restrictive blowpipe on that I have tried.

The round mouthpiece is threaded with a 30TPI thread onto the body which accomodates all mouthpieces included in the range of bagpipes from R.G. Hardie and is commonly used by other bagpipe makers.

The MaxiStick has an integral valve assembly which will allow the valve to be replaced when necessary. To access the valve unscrew the hemp part below the projection mount. We recommend smearing Vaseline on the valve for a better seal.

Q: Just want to make sure what length I am measuring. Do I measure the entire length of the blowpipe? Or just the length of the smooth portion? I just want to be sure. Thanks!

Asked by: Michael Clark - 8/30/2020

A: When you measure for a replacement blowpipe, you will measure it from the bottom of the projecting mount (not including the hemped area that fits into the blowpipe stock) to the tip of the mouthpiece!!!

Was this answer helpful? 4 of 4 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (8/31/2020)

Submit an answer

Q: What replacement valve do you need for the maxistick

Asked by: Joseph Ferrick - 2/2/2020

A: You can use the Airstream blowpipe replacement valve with this.

Was this answer helpful? 2 of 2 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (2/3/2020)

Submit an answer

Q: Does the MaxiStick blowpipe come with the mouthpiece? If not, then it is safe to assume that the length selection is for the blowpipe only?

Asked by: SDowns - 3/12/2020

A: Yes, there is a round mouthpiece included with the Maxi Stick!!!

Was this answer helpful? 2 of 2 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (8/31/2020)

Submit an answer

Q: Just want to confirm that a standard McCallum bagpipe mouthpiece will screw onto the MaxiStick blowpipe.

Asked by: Mike Ahnell - 2/16/2020

A: It is very close. You would need to build up the threads on the maxi stick a but with teflon tape, but that should do the trick!

Was this answer helpful? 1 of 1 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (2/16/2020)

Submit an answer

Q: Just want to make sure this will fit my McDougall pipes, circa 1880-1900? Likely the one without the imitation ivory.

Asked by: Michael Clark - 8/27/2020

A: Yes, this will work with your bagpipe! I would suggest the black projecting mount as I don't think that the imitation ivory will come close enough to match the mounts on your bagpipe.

Was this answer helpful? 1 of 2 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (8/31/2020)

Submit an answer

Q: MaxiStick blowpipe. How is the length measured? From bottom of projecting mount, is mouthpiece included in measurement? Also, do you have small cleaning swab for 3/8" diameter blowpipe? thanks, Doug Hubbard

Asked by: Douglas Hubbard - 1/11/2021

A: The blowpipe is measured from the bottom of the projecting mount (not including the hemped piece that goes into the stock) to the tip of the mouthpiece. We don't have a swab, but the chanter brush will do a fine job!

Was this answer helpful? 1 of 1 Customer(s) found this Answer helpful.

Answer provided by: Jon Maffett (1/11/2021)

Submit an answer

Questions about this item? Ask here.

MaxiStick Blowpipe

Choose Options

Rating Snapshot

Average Customer Ratings

Q: Just want to make sure what length I am measuring. Do I measure the entire length of the blowpipe? Or just the length of the smooth portion? I just want to be sure. Thanks!

Q: What replacement valve do you need for the maxistick

Q: Does the MaxiStick blowpipe come with the mouthpiece? If not, then it is safe to assume that the length selection is for the blowpipe only?

Q: Just want to confirm that a standard McCallum bagpipe mouthpiece will screw onto the MaxiStick blowpipe.

Q: Just want to make sure this will fit my McDougall pipes, circa 1880-1900? Likely the one without the imitation ivory.

Q: MaxiStick blowpipe. How is the length measured? From bottom of projecting mount, is mouthpiece included in measurement? Also, do you have small cleaning swab for 3/8" diameter blowpipe? thanks, Doug Hubbard

Related Items

Browse Similar Items

Recently Viewed Items

Mailing List